Genie INTELLIG 3024 Manual de usuario Pagina 9
- Pagina / 26
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
©2010 The Genie Company 01/27/2010
9
PROGRAM
SET
—
+
5 SECS
PROGRAM
SET
—
+
PRESS and HOLD
SEE BOTH
Blue LEDs
come ON
SEE one
Blue LED
come ON
PRESS a previously programmed Genie®
IntelliCode® 2 remote button on remote. If you
are unsure which remote you have see page 15.
Remote must be IntelliCode® 2 enabled.
RELEASE
1 2 3 4
OPTIONAL PROGRAMMING POWER HEAD TO
Homelink®, Car2U®, or IntelliCode® 1 REMOTES and SERIES II WIRELESS KEYPADS
To complete any of these tasks you MUST have at least one Genie® IntelliCode® 2 remote button already
programmed to the power head.
Homelink® or Car2U®: You must also have your Homelink® or Car2U® enabled vehicle present and their
programming instructions to perform these programming steps.
Genie® remote: You must also have your Genie® IntelliCode® 1 remote present.
Genie® wireless keypad: You must also have your Genie® wireless keypad installed and a PIN already programmed into the keypad.
PRESS and
RELEASE
5
On the IntelliCode® 1 remote PRESS
a button and RELEASE.
6
SEE both LEDs flash Blue.
IntelliCode® 1 remote or wireless keypad programming
7
On the IntelliCode® 1 remote PRESS
the same button and RELEASE.
The next press of the remote will
operate door.
5
Enter your wireless keypad PIN.
6
Press and hold button
(3 seconds) on wireless keypad and
see on power head long LED come ON
Purple. (You may have to press
more than once.)
8
Test. Repeat as necessary for any
other IntelliCode® 1 remotes.
7
Press and hold button
(3 seconds) on wireless keypad again
and see on power head both LEDs
come ON Blue.
8
Wait 30 seconds and test operation.
Genie® IntelliCode® 1 remote Genie® IntelliCode® 1 wireless keypad
SEE long Purple
LED flashing
SEE both LEDs
flash Purple
All optional programming is complete. Your garage door opener is ready to use.
5
For Car2U® enabled vehicles follow the Car2U®
instructions.
6
Test. Repeat as necessary for any other Car2U®
enabled vehicle.
Homelink® or Car2U® programming
If your Homelink® has been previously programmed to an
Genie® opener begin with Step 5.
If your Homelink® has not yet been linked to a Genie®
opener then go to page 15 and change one remote button
from IntelliCode® 2 to IntelliCode® 1, then program that
button to the power head and repeat steps 1-4 then
continue with Homelink® steps 5-6.
5
6
PRESS the Homelink® button twice.
Test. Repeat as necessary for any other pre-
programmed Homelink® enabled vehicle.
- IntelliG 1
- (Not available on all models) 3
- TABLE OF CONTENTS 4
- A) CLOSE DOOR TRAVEL LIMIT 6
- B) OPEN DOOR TRAVEL LIMIT 7
- FIG. 3-1 10
- FIG. 3-2 11
- AVERTISSEMENT 11
- ADVERTENCIA 11
- FIG. 3-3 12
- LED Colors 13
- Programming Overview 13
- Press Program LED Display 13
- Three button 15
- IMPORTANT SAFETY INSTRUCTIONS 17
- F DOOR B COMES OBSTRUCTED 18
- PULL DOWN ON HANDLE 18
- STB BWC IWC 19
- Chain at center of rail 20
- POWER CORD 21
- Speed Level 22
- Force Level 23
- Limited Warranty 26
Relacionado con productos y manuales para Abridor De Puerta De Garage Genie INTELLIG 3024
(2 paginas)
Bosch B5512 manuels
Manuels d'utilisation et guides de l'utilisateur pour Protection contre les incendies Bosch B5512.
Nous fournissons des manuels en pdf 1 Bosch B5512 à télécharger gratuitement par type de document : Manuel du propriétaire
Comentarios a estos manuales